Next Page. High definition sound bar with wireless subwoofer 32 pages. To prevent the HD Sound Bar System from being damaged, the following rules should be observed for its installation, use, and maintenance.
HD Sound Bar System is exposed to rain or other moisture. HD Sound Bar System is dropped or damaged in any way.
If you choose to mount the TV on the wall, please follow the instructions below for removing the stand. S S S S ubwoofer ubwoofer ubwoofer ubwoofer 1. Link Button — Refer to Chapter 3 — Setting up 2.
The first 7 white LEDs are volume indicators. Each LED has three brightness levels for a total of 21 volume settings. When you adjust the subwoofer level relative to the bar, the LEDs blink. Press inward to release the lock 1 , and at the same time, slide the battery holder out of the remote with your fingernail 2. The LED on the front of the subwoofer will flash quickly. Once pairing is requested, the device will attempt for up to 30 seconds and then end the pairing mode.
Page Chapter 7 Maintenance And Troubleshooting - If Error C, Overcurrent detection is indicated, reduce the volume setting of the Speaker Bar and Subwoofer temporarily, and turn the unit off for a short period and back on to reset the circuitry. If this indication continues to occur, then reduce the volume level for the particular source content being played. Page Troubleshooting Guide For more information on warranty service or repair, after the warranty period, please contact our Support Department at the number below.
Page Compliance The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. Page 27 What is not covered www. Page 31 MP3 Player Connection………………….. Print page 1 Print document 31 pages.
Rename the bookmark. Any other voltage than the specified voltage may cause fire or electric shock. For more information, contact your dealer.
This plug will fit only into a grounded power outlet. This is a safety feature. If your outlet does not accommodate the three-pronged, have an electrician install the correct outlet, or use an adapter to ground the HD Sound Bar System safely. To totally disconnect power, unplug the power cord.
Overloading can result in fire or electric shock. To avoid electric shock, avoid handling the power cord during electrical storms. Opening or removing the front cover may expose you to high voltages, electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to qualified service personnel. Continuous use in this case may result in fire or electric shock.
If any smoke or odor becomes apparent, unplug the power cord and contact your dealer immediately. If the HD Sound Bar System is dropped and the housing is damaged, the internal components may function abnormally.
Unplug the power cord immediately and contact your dealer for repair. Operating the HD Sound Bar System in environments with heavy dust or high humidity may cause fire or electric shock. Pulling on the power cord may damage the wires inside the cord and cause fire or electric shock. Incorrect polarity may cause the battery to leak which can damage the remote control or injure the operator. Important Safety Instructions Chapter 1 Installation Chapter 2 Basic Controls and Connections Rear Panel Connections Top Panel Buttons Installing the Battery in the Remote Control Remote Control Range Chapter 3 Connecting Equipment Connecting a TV Connecting a Cable or Satellite Box Connecting an MP3 Player Connecting a Computer Chapter 4 Setting Up Chapter 5 Operation Audio Adjustments Chapter 7 Maintenance and Troubleshooting Troubleshooting Guide Chapter 8 Miscellaneous Information If you choose to mount the TV on the wall, please follow the instructions below for removing the stand.
The two feet provided with the HD Sound Bar System can be used as brackets if it is to be wall mounted. Using a screwdriver, remove the stands from their original configuration as shown in Fig. Link Button — Refer to Chapter 3 — Setting up. Input — Use this button to select the input desired.
This button doubles as a Link button when used during the pairing procedure. Holding the button for more than 3 seconds activates the pairing mode for the wireless link. Once pairing is requested, the device will attempt for up to 30 seconds and then end the pairing mode. Please refer to Page 17 for additional information. Vol - — Pressing this button will decrease the volume level. TVOL— Pressing this button will set the sound system to have control over the level of the audio output, preventing commercials on regular programming to become louder than the volume of the program being viewed.
There are a total of 10 LEDs. The first 7 white LEDs are volume indicators. Each LED has three brightness levels for a total of 21 volume settings. When you adjust the subwoofer level relative to the bar, the LEDs blink. Displayed as a bar graph representing the system volume, increasing from the left across the display.
The display is constantly on when active. Displayed as a bar graph representing the subwoofer volume, increasing from the left across the display. LED 5, 6 and 7 from left function as Input indicators.
Pressing the Input button on the top of the Sound Bar or the remote will step through the inputs. The next LED is the link indicator. It is orange. When the bar and sub are linked the light is solid. It blinks during the pairing process. Glows blue when on.
0コメント