If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Page 17 U. Page 18 Connect surround speakers 4, 5 to these terminals.
Cable indications For analog signals left analog cables right analog cables For digital signals optical cables coaxial cables For video signals video cables S-video cables If you experience poor reception quality, an outdoor antenna may improve the quality.
None Other models Be sure this unit is in the standby mode. The supplied optimizer microphone collects and analyzes the sound your speakers produce in your actual listening environment. If there is too much ambient noise, the results may not be satisfactory.
Unplug HP Headphones are connected. Page 35 Select a sound field program if desired. See page 55 for details about sound field programs. When playing these kinds of discs with 6. Automatic tuning is effective when station signals are strong and there is no interference.
Automatic tuning U. Page Presetting Stations Manual tuning If the signal from the station you want to select is weak, tune into it manually. Manually tuning into an FM station will automatically switch the tuner to monaural reception to increase the signal quality.
After about 5 seconds, automatic presetting starts from the frequency currently displayed and proceeds toward the higher frequencies. Press h to select a higher preset station number. Press l to select a lower preset station number. The preset group and number appear on the front panel display along with the station band, frequency and the TUNED indicator lights up.
The stations stored at the two preset assignments are exchanged. XM Satellite Radio is the satellite radio service with millions of listeners across the U. It is much easier to see the available information than reading it on the front panel display. For example, to enter the number , press the numeric buttons as shown below. The group letter appears. Page 57 Status and error messages If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display.
In this case, read the cause and follow the corresponding remedies. Refer to the operating instructions for those components. Set the input mode to AUTO see page 36 to enable this unit to automatically switch to the appropriate digital decoder according to the input signal. This program creates the extremely wide sound field of a mm movie theater. It precisely reproduces the source sound in detail, making both the video and Spectacle the sound field incredibly real.
Program selection methods vary depending on sound field program types. Remote control Program If you display the SET MENU and sound field program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display. Change the initial settings indicated in bold under each parameter to reflect the needs of your listening environment. INI Initializes the parameters of a group of sound field programs.
The unit directs the entire range of the surround back channel signal to the left surround back speaker. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Page 71 Low-frequency effect level Use to adjust the output level of the LFE low-frequency effect channel according to the capacity of your subwoofer or headphones. The LFE channel carries low- frequency special effects which are only added to certain scenes.
INI Use this feature to initialize the parameters for each sound field program within a sound field program group. When you initialize a sound field program group, all of the parameter values within that group revert to their initial settings. Use to switch the speaker impedance for this unit. To control other components, you must set up remote control with the appropriate remote control codes.
Press an input selector button or select the component you want to set up. Note that some buttons may not correctly operate the selected component. Use the input selector buttons to select the component you want to operate. Page Switching Library Codes To operate this unit using an alternative code.
In this case, set one of the alternative codes to operate this unit separately. Page Zone 2 U. If you own these products, you may not need to use an infrared emitter. Full screen Standard. Page of Go. PART H. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,.
If the product has been dropped or damaged in any way, and. When the product exhibits a distinct change in perfor- mance - this indicates a need for service. Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Wall or Ceiling Mounting — The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.
0コメント